Eagle ADC Example - Revision history

Support at 01:02, 20 June 2010

Support — Sun, 20 Jun 2010 01:02:57 GMT

← Older revision		Revision as of 01:02, 20 June 2010
Line 1:		Line 1:
	=Analog to Digital Converter (ADC)=		=Analog to Digital Converter (ADC)=
-	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html ~~Eagle50~~], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==	+	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle 50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==

	The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:		The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:

Support at 00:59, 20 June 2010

Support — Sun, 20 Jun 2010 00:59:07 GMT

← Older revision		Revision as of 00:59, 20 June 2010
Line 1:		Line 1:
-	~~__TOC__~~
	=Analog to Digital Converter (ADC)=		=Analog to Digital Converter (ADC)=
	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==		==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==

Support at 15:46, 17 June 2010

Support — Thu, 17 Jun 2010 15:46:46 GMT

← Older revision		Revision as of 15:46, 17 June 2010
Line 1:		Line 1:
		+	__TOC__
	=Analog to Digital Converter (ADC)=		=Analog to Digital Converter (ADC)=
	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==		==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==

Support at 15:35, 17 June 2010

Support — Thu, 17 Jun 2010 15:35:51 GMT

← Older revision		Revision as of 15:35, 17 June 2010
Line 3:		Line 3:

	The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:		The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:
-	[{Image:Eagle_ADC.png\|center\|]]	+	[[Image:Eagle_ADC.png\|center\|]]
	This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.		This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.
	[[Image:Eagle_ADC1.gif\|center\|]]		[[Image:Eagle_ADC1.gif\|center\|]]

Support at 15:35, 17 June 2010

Support — Thu, 17 Jun 2010 15:35:37 GMT

← Older revision		Revision as of 15:35, 17 June 2010
Line 3:		Line 3:

	The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:		The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:
-	[Image:Eagle_ADC.png\|center\|]]	+	[{Image:Eagle_ADC.png\|center\|]]
	This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.		This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.
	[[Image:Eagle_ADC1.gif\|center\|]]		[[Image:Eagle_ADC1.gif\|center\|]]

Support at 15:35, 17 June 2010

Support — Thu, 17 Jun 2010 15:35:19 GMT

← Older revision		Revision as of 15:35, 17 June 2010
Line 1:		Line 1:
	=Analog to Digital Converter (ADC)=		=Analog to Digital Converter (ADC)=
	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==		==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==
		+
	The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:		The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:
	[Image:Eagle_ADC.png\|center\|]]		[Image:Eagle_ADC.png\|center\|]]
	This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.		This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.
	[[Image:Eagle_ADC1.gif\|center\|]]		[[Image:Eagle_ADC1.gif\|center\|]]

Support at 15:34, 17 June 2010

Support — Thu, 17 Jun 2010 15:34:58 GMT

← Older revision		Revision as of 15:34, 17 June 2010
Line 1:		Line 1:
	=Analog to Digital Converter (ADC)=		=Analog to Digital Converter (ADC)=
	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==		==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==
		+	The TI LM3S microcontrollers used in the Eagle controller line support eight single ended or four differential 10-bit analog inputs with a sampling rate up to 500 kilo-samples/sec (kSPS). These signals are available in the following headers:
		+	[Image:Eagle_ADC.png\|center\|]]
		+	This example shows you how to read voltages from the 8 ADC channels. The screen output is shown below. Note that the voltages are shown in both integer and floating point formats. In integer format the 10-bit values go between 0 and 1023 (0x03FF) for the range 0.00V to 3.00V resulting in an accuracy of +/- 1.465 mV. Note that voltages over 3V should not be applied to the ADC inputs as they could damage the microcontroller. Op-amps or other alternatives should be used to implement scaling and isolation.
		+	[[Image:Eagle_ADC1.gif\|center\|]]

Support: /* Analog to Digital Converter (ADC) */

Support — Thu, 17 Jun 2010 15:30:22 GMT

Analog to Digital Converter (ADC)

← Older revision		Revision as of 15:30, 17 June 2010
Line 1:		Line 1:
	=Analog to Digital Converter (ADC)=		=Analog to Digital Converter (ADC)=
-	==Compatibility[http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50]==	+	==Compatibility [http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50], [http://www.micromint.com/index.php/SBC/eagle-50.html 50E], [http://www.micromint.com/index.php/SBC/eagle-100.html 100]==

Support: Created page with '=Analog to Digital Converter (ADC)= ==Compatibility[http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50]=='

Support — Thu, 17 Jun 2010 15:29:03 GMT

Created page with '=Analog to Digital Converter (ADC)= ==Compatibility[http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50]=='

New page

=Analog to Digital Converter (ADC)=
==Compatibility[http://www.micromint.com/index.php/SBC/eagle-50.html Eagle50]==