Lincoln Timer to Generate Different Delays - Revision history

Support at 16:02, 12 April 2012

Support — Thu, 12 Apr 2012 16:02:07 GMT

← Older revision		Revision as of 16:02, 12 April 2012
Line 8:		Line 8:
	* 2. Program the Lincoln with the binary.		* 2. Program the Lincoln with the binary.
	* 3. Press the "RESET" button.		* 3. Press the "RESET" button.
-	* 4. Observe the signal on J2 pin 19 (MAT0.0) with an oscilloscope.	+	* 4. Enter the delay time for the first delay.
		+	* 5. Enter the delay time for the second delay.
		+	* 6. Observe the signal on J2 pin 19 (MAT0.0) with an oscilloscope.

Support: /* Compatibility Lincoln 60, Lincoln 60E */

Support — Thu, 12 Apr 2012 15:41:54 GMT

Compatibility Lincoln 60, Lincoln 60E

← Older revision		Revision as of 15:41, 12 April 2012
Line 14:		Line 14:


-	Below is a screen capture of the signal when 002 was entered for the first delay time and 001 was entered for the second delay time.	+	Below is a screen capture of the signal when 002 was entered for the first delay time and 001 was entered for the second delay time. The signal is high for the first delay time and low for the second delay time.


	[[Image:Lincoln_timer_gen_diff_delay2.png\|center\|]]		[[Image:Lincoln_timer_gen_diff_delay2.png\|center\|]]

Support: /* Compatibility Lincoln 60, Lincoln 60E */

Support — Thu, 12 Apr 2012 15:40:33 GMT

Compatibility Lincoln 60, Lincoln 60E

← Older revision		Revision as of 15:40, 12 April 2012
Line 12:		Line 12:

	[[Image:Lincoln_timer_gen_diff_delay.png\|center\|]]		[[Image:Lincoln_timer_gen_diff_delay.png\|center\|]]
		+

	Below is a screen capture of the signal when 002 was entered for the first delay time and 001 was entered for the second delay time.		Below is a screen capture of the signal when 002 was entered for the first delay time and 001 was entered for the second delay time.

Support: Created page with '==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]== This example applicatio…'

Support — Thu, 12 Apr 2012 15:40:08 GMT

Created page with '==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]== This example applicatio…'

New page

==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]==

This example application demonstrates how to use Timer Match to generate different delay signals. Timer 0 generate two delays and output a signal on MAT0.0 (J2 pin 19). The first UART, which is connected to the COM1 on the Lincoln microcontroller board, is configured for 115,200 bits per second, and 8-n-1 mode. When the program is started a message will be printed to the terminal. The below screen shot is of the timer_gen_diff_delay in action.

Please follow these steps to run the timer_gen_diff_delay example:

* 1. Compile the timer_gen_diff_delay example.
* 2. Program the Lincoln with the binary.
* 3. Press the "RESET" button.
* 4. Observe the signal on J2 pin 19 (MAT0.0) with an oscilloscope.

[[Image:Lincoln_timer_gen_diff_delay.png|center|]]

Below is a screen capture of the signal when 002 was entered for the first delay time and 001 was entered for the second delay time.

[[Image:Lincoln_timer_gen_diff_delay2.png|center|]]