Lincoln CAN Example
From Manuals
(Difference between revisions)
(Created page with '=Controller Area Network (CAN)= ==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincol…') |
(→Compatibility Lincoln 60, Lincoln 60E) |
||
| (2 intermediate revisions not shown) | |||
| Line 3: | Line 3: | ||
==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]== | ==Compatibility [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60], [http://www.micromint.com/index.php/SBC/lincoln60.html Lincoln 60E]== | ||
| - | The I/O Plus option for the Lincoln | + | The I/O Plus option for the Lincoln adds a CAN tranceiver. In order to run this example you will need the following equipment: |
| - | + | * 1. Two Lincolns with the I/O Plus Option populated | |
| + | * 2. Two COM ports on a computer | ||
| + | * 3. One 2x5 to 2x5 straght through ribbon cable | ||
| + | Please follow these steps to run the CAN example: | ||
| - | [[Image:Lincoln_can_rx.png|center|]] | + | * 1. Compile the example with the "#define CAN_TRANSMIT" set to 1 |
| + | * 2. Program one of the Lincolns with the binary and this will be the Lincoln used to transmit CAN messages | ||
| + | * 3. Compile the example with the "#define CAN_TRANSMIT" set to 0 | ||
| + | * 4. Program the other Lincoln with the binary and this will be the Lincoln used to receive CAN messages | ||
| + | * 5. Disconnect the power to both boards | ||
| + | * 6. Connect the two boards together with the 2x5 to 2x5 ribbon cable on J13 | ||
| + | * 7. Open a terminal window for each board set to 115200, 8 data bits, no parity, 1 stop bit, and no hardware handshaking | ||
| + | * 8. Connect a COM port to COM1 of each Lincoln board | ||
| + | * 8. Apply power to the Lincoln that will receive the CAN messages | ||
| + | * 9. Apply power to the Lincoln that will transmit the CAN messages | ||
| + | |||
| + | The following screen shots are of the CAN example in action. | ||
| + | |||
| + | [[Image:Lincoln_can_tx.png|center|alt=Lincoln-60|frame|<div align="center">'''Lincoln programmed for CAN to transmit]] | ||
| + | |||
| + | |||
| + | [[Image:Lincoln_can_rx.png|center|alt=Lincoln-60|frame|<div align="center">'''Lincoln programmed for CAN to receive]] | ||
Current revision as of 21:51, 11 March 2011
Controller Area Network (CAN)
Compatibility Lincoln 60, Lincoln 60E
The I/O Plus option for the Lincoln adds a CAN tranceiver. In order to run this example you will need the following equipment:
- 1. Two Lincolns with the I/O Plus Option populated
- 2. Two COM ports on a computer
- 3. One 2x5 to 2x5 straght through ribbon cable
Please follow these steps to run the CAN example:
- 1. Compile the example with the "#define CAN_TRANSMIT" set to 1
- 2. Program one of the Lincolns with the binary and this will be the Lincoln used to transmit CAN messages
- 3. Compile the example with the "#define CAN_TRANSMIT" set to 0
- 4. Program the other Lincoln with the binary and this will be the Lincoln used to receive CAN messages
- 5. Disconnect the power to both boards
- 6. Connect the two boards together with the 2x5 to 2x5 ribbon cable on J13
- 7. Open a terminal window for each board set to 115200, 8 data bits, no parity, 1 stop bit, and no hardware handshaking
- 8. Connect a COM port to COM1 of each Lincoln board
- 8. Apply power to the Lincoln that will receive the CAN messages
- 9. Apply power to the Lincoln that will transmit the CAN messages
The following screen shots are of the CAN example in action.
Lincoln programmed for CAN to transmit
Lincoln programmed for CAN to receive