From Manuals

Revision as of 13:27, 17 June 2010

Boot from SD/MMC

Creating a Bootable Filesystem on SD card

1) The first step is to make a bootable file system on the SD card. Insert the card into the slot of a running plug. Enter the following commands:

>fdisk /dev/mmcblk0
press "o"  / create a new partition table
press "n"  / create a new partition
press "p"  / it's a primary partition
press "1"  / partition #1
press enter / default first cylinder
press enter / default last cylinder
press "a"  / set the boot flag
press "1" / ... for partition #1
press "w" / save changes
	
>mkfs -t ext2  /dev/mmcblk0p1
>mkdir /mnt/sdcard
>mount /dev/mmcblk0p1 /mnt/sdcard
>df

2) Now copy your existing nand file system onto the sd card. This may take 5-10 minutes.

root#: cp -r /rootfs/* /mnt/sdcard

3) The SD card should now mirror your internal nand flash, which you can confirm with df -h, etc.

Filesystem           1K-blocks      Used Available Use% Mounted on
rootfs                  519168    185612    333556  36% /
tmpfs                   257816         0    257816   0% /lib/init/rw
varrun                  257816       260    257556   1% /var/run
varlock                 257816         0    257816   0% /var/lock
udev                    257816        12    257804   1% /dev
tmpfs                   257816         0    257816   0% /dev/shm
tmpfs                   257816     21824    235992   9% /var/cache/apt
/dev/mmcblk0p1         7707056    516216   6799340   8% /mnt/sdcard

your SD card now has a bootable system. The next step is to boot it.

Booting from the SD Card

You need to interact with u-boot now. You must do this from a program talking to the usb-serial port, not from an ssh shell (duh).

>shutdown -r now

When u-boot appears, stop it by typing ENTER a few times, to stop it from booting automatically.

Electrum>> printenv bootargs
bootargs console=ttyS0,115200 root=/dev/nfs rw ip=192.168.1.231:192.168.1.249::255.255.255.0::
eth0: nfsroot=192.168.1.249:/media/disk/rootfs

This is the line that you'll need to change. Change it to

Electrum>> setenv bootargs console=ttyS0,115200 root=/dev/mmcblk0p1 rw ip=192.168.1.231:192.168.1.249::255.255.255.0::
eth0:none
Electrum>> printenv bootargs (if you like, just to confirm that you did it right)
Electrum>> boot

To boot Kernel and Rootfs from SD/MMC card (Without NAND)

1) Download u-boot-2010.03. (Its recommended that load can be built before going further)

2) Copy board/micromint folder and /include/configs/electrum100.h from u-boot-2009.08.

3) Add the following Configurations to enable MMC support.

#define CONFIG_CMD_EXT2	1
#define CONFIG_CMD_FAT	1
#define CONFIG_MMC	1
#define CONFIG_GENERIC_MMC	1
#define CONFIG_CMD_MMC	1
#define CONFIG_GENERIC_ATMEL_MCI 1
#define MMCI_BASE		0xFFFA8000

4) Then create an init routine in your platform code:

/* this is a weak define that we are overriding */
#ifdef CONFIG_GENERIC_ATMEL_MCI
int board_mmc_init(bd_t *bd)
{
	at91_mci0_hw_init((1 << 0) || (1 << 1));
	/* This calls the atmel_mmc_init in gen_atmel_mci.c */
       return atmel_mmc_init(bd);
}
#endif 

5) Change line 86 of uboot*/cpu/arm926ejs/at91/at91sam9260_devices.c to

#if defined(CONFIG_ATMEL_MCI) || defined(CONFIG_GENERIC_ATMEL_MCI)

6) Apply the following patch: http://www.mail-archive.com/u-boot@lists.denx.de/msg31713.html

7) Build the u-boot-2010.03

$make bootloader

8) Update the Boot strapper and Boot-loader into Electrum100 using SAM-BA application

9) Execute the command:

Electrum>> mmc list 
Electrum>> mmc rescan 0

10) Now copy the Kernel Image and rootfs into SD card (Refer the section: Creating a Bootable filesystem on SD card).

11) Check the card using "mmc rescan 0" command

12) change the boot args to load root file system from SD card.

bootargs console=ttyS0,115200 root=/dev/mmcblk0p1 rw ip=192.168.1.231:192.168.1.249::255.255.255.0::eth0:none

13) To load the Kernel from EXT2 change the boot commands

Electrum>> setenv bootcmd mmcinfo\; ext2load mmc 0:1 0x22000000 uImage-2.6.31.9\; bootm
Electrum>> saveenv
Electrum>> reset